Enclave is an older 3rd person view hack-n-slash game where you progress through small linear maps. Fight Orcs, Goblins, theifs and other monsters. The story is simple, the quests are linear, its a fun button masher for quick gaming satisfaction.
![]()
![]()
Follow my step-by-step guide on installing, configuring and optimizing Enclave in Linux with PlayOnLinux.
Note: This guide applies to the GOG version of Enclave. Other versions may require additional steps.
Tips & Specs:
To learn more about PlayOnLinux and Wine configuration, see the online manual: PlayOnLinux Explained
int 17 64-bit
PlayOnLinux: 4.2.4
Wine: 1.6.2
Wine Installation
Click Tools
Select "Manage Wine Versions"
![]()
Look for the Wine Version: 1.6.2
Note: Try using stable Wine 1.8 and 1.8-staging
Select it
Click the arrow pointing to the right
![]()
Click Next
Downloading Wine
![]()
Extracting
Downloading Gecko
![]()
Installed
![]()
Wine 1.6.2 is installed and you can close this window
PlayOnLinux Setup
Launch PlayOnLinux
Click Install
![]()
Click "Install a non-listed program"
![]()
Click Next
Select "Install a program in a new virtual drive"
Click Next
![]()
Name your virtual drive: enclave
Click Next
![]()
Check all three options:
Click Next
- Use another version of Wine
- Configure Wine
- Install some libraries
![]()
Select Wine 1.6.2
Click Next
![]()
Select "32 bits windows installation"
Click Next
![]()
Wine Configuration
Applications Tab
Windows Version: Windows 7
Click Apply
![]()
Graphics Tab
Check "Automatically capture the mouse in full-screen windows"
Check "Emulate a virtual desktop"
Desktop Size: 1024x768
Click OK
![]()
PlayOnLinux Packages (Libraries, DLLs, Components)
Check the following Packages:
Click Next
- POL_Install_corefonts
- POL_Install_d3dx9
- POL_Install_gdiplus
- POL_Install_tahoma
Note: All packages will automatically download and install
Installing Enclave
Click Browse
![]()
Select "setup_enclave_2.0.0.2.exe"
Click Open
![]()
Click Next
Check "Yes, I have read and accept EULA"
Click Options
Uncheck "Create desktop icons"
Click Install
![]()
Setup error
You may see this error, just click OK
![]()
Click Exit
![]()
PlayOnLinux Shortcut
Select "Enclave.exe"
Click Next
![]()
Name your shortcut: Enclave
Click Next
![]()
Click Next
PlayOnLinux Configure
Back to PlayOnLinux
Select Enclave
Click Configure
![]()
General Tab
Wine Version: 1.6.2
Note: Click the + to download other versions of Wine. Click the down-arrow to select other versions of Wine.
![]()
Display Tab
Video Memory size: select the amount of memory your video card/chip uses
![]()
Close Configure
Launching Enclave
Back to PlayOnLinux
Select Enclave
Click Run
Note: Click debug to see errors and bugs
![]()
Select Options
![]()
Select Video
Set the resolution to match your Linux desktop for fullscreen
![]()
Select Graphics
Adjust decals, shadows, Level of Detail and surfaces
![]()
Select Textures
Adjust world and character textures
Increase or decrease anisotrophy
![]()
Rule of thumb:
High Setting = More detail, lower frame rates
Low Setting = Less detail, higher frame rates
Conclusion:
Enclave ran extremely well since it is a directx 9 game from GOG.com
I cranked everything to high and it supported high resolutions.
I was impressed with the texture quality and the lighting for such an old game.
Enclave should run on any laptop and maybe even some netbooks.
Gameplay Video
Screenshots:
![]()
![]()
![]()
![]()
![]()
![]()
Comments
Discussion in 'Guides' started by booman, Sep 19, 2014.
Page 1 of 2
Page 1 of 2
XenPorta
© Jason Axelrod from 8WAYRUN.COM